Please enable JS

Gasfitting tech tips

Do you want to translate the page?

Free course! Building Code modules

This is a helpful introduction to understanding the Building Code (30 min duration).  This course is open to everyone.

Find out more about:

  • The Building Code, Building Performance Requirements, and Building Consent Compliance

Check it out  [ HERE ]

Note: if you wish to complete the assessment and record your learning, you will need to create an account and login.

View the following gas installation standards from your Trade-login

Mandatory performance requirements for gas installations are detailed in Section 2 of AS/NZS 5601 Parts 1 and 2.

  • Section 2.2.8 of AS/NZS 5601.1 and 2.9.8 of AS/NZS 5601.2 requires all installations to be commissioned and provide commissioning check sheets in the appendices.   Appendix O and I of Part 1 and 2 respectively state the same procedures should be followed for re-commissioning an appliance after maintenance or repair.  The appendices Q and K should also be used as these check sheets assist in ensuring the installation has been carried out correctly.
  • Appendix O - Guidelines for gas appliance commissioning
  • Appendix Q - Gas installation checklist
  • Appendix R - Spillage tests for flued appliances

If you are checking an existing gas installation for safety the NZ standard NZS 5255 is a good document to use.

  • NZS 5255 : Safety verification of existing gas installations

Tech sheets:

Governing legislation and important compliance documents

Click through to the Legislation Hub 

In this hub we keep you informed on governing legislation and important compliance documents that assist you to keep it legal.

You can also find links to the policies adopted by the Board here.

Be safe around arc flash hazards

The definition of an arc flash is "an undesired electric discharge that travels through the air between conductors or from a conductor to a ground."

The arc flash is a part of an arc fault, which is an example of an electrical explosion caused by a low-impedance connection that goes through the air to the ground. 

When an arc flash occurs it creates a very bright light and intense heat.

In addition, it has the potential to create an arc blast, which can cause a traumatic force that can severely injure anyone in the area or damage anything nearby.

Go to the link below, which will give employees and management an overview of what needs to be done to keep safe around areas that can be dangerous.

Health and Safety at Work Act

The working together on health and safety presentation provides you with the basic facts you need to know about the Health and Safety at Work Act (HSWA). It covers the main concepts at a high level.

Supervision guidelines

Everything you need to know it get it right

Templates are included in this download

Advance your career and earning potential by upskilling

In the current climate, business and tradespeople may want to consider ways to diversify their skill set and provide new earning opportunities.  Here are a few opportunities businesses and tradespeople may want to consider.

Associated Tradesperson 

Become an Associated Tradesperson. This class of registration sits under the Electrical Workers Registration Board (EWRB).

It allows registered plumbers and/or gasfitters to do a limited amount of restricted electrical work relating to their trade.

Those that hold this registration can do maintenance and replace fittings that have an electrical rating of not more than 250 volts and 16 amperes on a limited amount of appliances.

For example, an Associated Tradesperson Plumber can replace an element in a storage water heater; an Associated Tradesperson Gasfitter can replace electrical fittings that form part of gas fired equipment; or an Associated Tradesperson Plumber/Gasfitter can do both.

Find out more at

Independent Qualified Person (IQP) backflow prevention

Become an IQP for testing backflow prevention devices. An IQP can test backflow prevention devices, but only an authorised plumber can install and repair them.

Becoming an IQP allows plumbers to expand the work, which they are authorised to do. Testing is required every 12 months for many backflow prevention devices.

Therefore, becoming an IQP can add a regular income stream to a business. The territorial authority (e.g. your local council) determines who can become an IQP. Generally, a territorial authority will require training in backflow prevention then registering with them.

For more information, contact your local council.

Become registered in all three trades 

Become registered in all three trades (plumbing, gasfitting and drainlaying). Having an extra registration vastly increases your value to a company and the work, which you can do.

This can save your business and your client money by not having to outsource to other tradespeople in order to complete work that requires the different authorisations.

In the last few years, the Board has worked hard to create new pathways for people to become registered. This includes – the opportunity for oral examinations for people with learning difficulties; and the Skills Recognition of Current Competency (RCC) assessment for people that have been working in the trade for many years but never completed the formal training.

If you are not registered in all three trades (plumbing, gasfitting or drainlaying) contact the Boards registration team for advice on what pathway would be most suitable for your situation or the Skills organisation for information on training.

In some cases, the training for the national certificate in another trade may take as little as 2-2 ½ years.

Contact 0508 Skills (0508 754 557)

Contact the Board 0800 743 262

Service Agent

Becoming a service agent opens up the earning potential for a tradesperson and/or company.

Many manufacturers require people to be a service agent in order to do maintenance on their products.

A person may be legally authorised to do maintenance on some products but in many circumstances, unless they are a service agent they void the warranty on the product.

If a person or company are wanting to upskill and become a service agent, they should contact the manufacturer of the products they would like to service.

The manufacturer can guide them on what they require for someone to become a service agent for them.

0800 743 262

It's a hot-line to point you in the right direction.

If you are unsure, this is the support that will ensure you have all the information you need to help you get it right with essential decision making.